This is an old revision of the document. It contains one or more snippets which may be outdated.
Replace outdated snippets in this Old Revision?Yes No

JES t/SIG-D Traffic light controller

Features

Switching and monitoring of traffic lights
Up to 2 traffic lights can be switched via one device
1-, 2- or 3-signal traffic lights configurable
Monitoring of light bulb and LED inserts both switched on and off
Reduced brightness at night by second supply voltage
Freely configurable operating/fault messages for each of the two traffic lights
Connection to and control by PLC via
- Digital inputs/outputs
- MODBUS/TCP
- MODBUS RTU
Touch display in the front panel for signalling the traffic light status and for manual switching on site
35 mm DIN rail mount

System

Traffic light controller with touch display
Optional transformer for providing a lower supply voltage to reduce brightness at nighttime

Function

Traffic lights in tunnels are essential for influencing traffic in the event of hazards or accidents. The status of such traffic lights must be monitored to ensure tunnel safety. A traffic light in the tunnel is usually controlled by the tunnel control system. It is connected to the signal monitoring device via conventional PLC inputs and outputs. The traffic light controller switches the signals (red, yellow, green) on and off as given by the outputs of the tunnel control system and reports back the status of the traffic light. In the event of faults such as broken wires or a defective light source, an error message is issued even when the respective signal is currently in switched off state.

Advantages

Specially designed for use in front of and in tunnels
Mounting on DIN rail for easy installation and replacement
Suitable for conventional lamps and LED technology
Display for indicating signal status and faults
One device for monitoring up to two traffic lights
On-site control via a touch display
Freely configurable error or operating messages via web server
Monitoring of signals both in switched-on and switched-off state

Application

Tunnels are important infrastructure elements in road networks and facilitate the connection of regions.

Environmental conditions in tunnels are influenced by fog, particles and emissions and need to be monitored to protect people on their passage through the tunnel from danger and impacts on their health. Accidents in tunnels, and particularly fires, can have dramatic consequences and can prove extremely costly in terms of human life, increased congestion, pollution and repair costs. At every time people in the tunnel need to be supplied with breathable air and sufficient visibility.

Since 1990 JES Elektrotechnik GmbH develops, installs and maintains systems to monitor air characteristics and lighting conditions in tunnels. Our systems are robust, durable and resistant against the corrosive atmosphere in a tunnel. They operate reliably and have a high accuracy in measurement.

All systems fulfil the requirements of the EC guideline 2004/54/EC (Minimum safety requirements for tunnels in the trans-European road network) and the more detailed national guidelines and provisions:

Austria: RVS 09.02 Tunnelausrüstung
Germany: RABT Richtlinien für die Ausstattung und den Betrieb von Straßentunneln
Switzerland: ASTRA Richtlinien und Fachhandbuch Betriebs- und Sicherheitsausrüstungen (BSA)

Our range of products for tunnel covers systems for monitoring of

Visibility (extractive or in-situ)
Toxic gases like CO, NO, NO₂ (extractive or in-situ)
Air velocity, direction and temperature
Luminance (access, threshold and interior zone)
Illuminance

Technical specifications

Überwachung von Verkehrslichtsignalgebern mit Glühlampen oder LED-Einsätzen
Signalgeber	Bis zu 2, gemeinsam oder getrennt ansteuerbar
Signale	1-, 2- oder 3-begriffige Signalgeber frei konfigurierbar
Blinktakt	Muss extern generiert werden
Unterstützte Leuchtmittel	0 - 230 VAC, 60 Hz, max. 100 W 0 - 60 VDC, max. 30 W
Nachtabsenkung / zweite Helligkeitsstufe	Über zweite (niedrigere) Versorgungsspannung
Arbeitsstromfehler	< 50 % des konfigurierten Nennstroms
Ruhestromfehler	> 30 mA oder > 3 V gegen N

Traffic signal controller
Type	t/SIG-D
Operating voltage	24 VDC ± 10 %
Current consumption	max. 150 mA (controller only)
IP rating	IP20
Appliance class	II (double insulated)
Interfaces	Ethernet: MODBUS/TCP and web server for configuration RS485 MODBUS-RTU
Digital inputs	1 x per signal (total 6) 2 x select night / alternative operating voltage
Digital outputs	1 x signal status (total 6) when operating with 2 traffic lights 1 x signal status, 1 x signal (total 3+3) error when operating with 1 traffic light 2 x operation / fault signal
Output rating	24 VDC, max. 50 mA
Mount	35 mm DIN rail
Width	45 mm
Height	120 mm
Depth	120 mm
Space requirement	45 x 140 x 120 mm
Weight	300 g

Konformitäten

Konformitäten
Elektrische Normen	2014/35/EU Niederspannungsrichtlinie (LVD) 2014/30/EU Elektromagnetische Verträglichkeit (EMV) EN IEC 61000-6-2:2005 Störfestigkeit für Industriebereiche EN IEC 61000-6-3:2007 + A1: 2011 Störaussendung für Wohnbereich, Geschäfts- und Gewerbebereiche sowie Kleinbetriebe